Heater Treater Quick-Connect.
Set it. Connect it. Light it.
A complete BMS and fuel train on one welded stand — shop-built, pressure-tested, and ready to set in days, not weeks. Direct replacement for a Platinum 600, plug-and-play swap for Profire. Runs on facility 12–24 V DC or a solar package we build in-house.
One skid. Everything on it.
Every quick-connect unit ships as a complete, tested package — the controller and the entire gas train, plumbed on one frame, ready to connect. The fabrication happens in our shop, not on your location.
Built in days. Swapped in hours.
We build the controller, the gas train, the stand, and the solar package ourselves in Odessa — nobody in the chain is waiting on an OEM lead time. A unit goes from order to ready-to-set in days, and your retrofit goes from a day of field fabrication to a few hours of connections.
Power it your way
Facility power at 12–24 V DC — or no facility power at all. The ROS-built solar + dual-battery package (panel, batteries, charge controller) mounts on the same stand. No trenching, no generator, and since the BMS runs fully offline, no cell service either.
Set your oil temperature, ignition, and flame proving from the 10.1" touchscreen in the door — or from your phone at igniter.local. No laptop, no vendor software, no monthly fee.
Replacing a Platinum 600 or Profire?
The quick-connect unit was designed around the two controllers most common on Permian treaters. Your existing field devices — thermocouple, flame rod, ignition — land on a documented terminal map, and the gas train arrives already built, so the old panel's condition doesn't matter.
A direct replacement — same fired equipment, same field devices, modern controller, complete new gas train. Read the full Platinum 600 replacement guide →
Plug-and-play. The quick-connect lands the same field wiring a Profire install uses — no burner, valve, or sensor replacement required in most swaps. Fleet standardization runs a few hours per unit.
How the swap works
Identify
Text a photo of your existing panel and burner to (432) 227-4106. We confirm what you're running and what carries over.
Build & test
Plumbed, wired, and pressure-tested in our Odessa shop — a build measured in days, because we build every piece ourselves.
Set & connect
The stand sets next to the treater. Connect fuel gas, pilot and main runs, land the thermocouple and flame rod — existing field devices reuse.
Light & verify
We commission on-site: prove flame, verify lockout and ESD response, set your oil temperature, and walk your operator through the touchscreen.
Quick-connect questions.
What exactly comes on the stand?
+
Everything between your fuel gas supply and the burner: the ROS Wi-Fi BMS in a NEMA 4X enclosure with a built-in 10.1" touchscreen, a 1" ASCO emergency-shutdown solenoid on the main fuel run, a 1/4" Parker pilot solenoid, a 1/4" Parker main solenoid, a FloPro D2T main burner control valve, pilot and main regulators with gauges, and a manual isolation valve — all plumbed on a welded steel stand and pressure-tested before it leaves our Odessa shop.
How fast can I get one?
+
Days, not weeks. We build the controller, the gas train, and the stand ourselves in Odessa, so there's no OEM lead time anywhere in the chain. Text a photo of your treater's existing panel to (432) 227-4106 and we'll confirm the build spec and give you a real date.
Does it replace a Platinum 600?
+
Yes — it's a direct replacement. Same fired equipment, and your existing field devices (thermocouple, flame rod, ignition) land on a documented terminal map. The gas train arrives already built, so the condition of the old panel doesn't matter.
What about Profire-controlled treaters?
+
Plug-and-play. The quick-connect unit lands the same field wiring a Profire install uses — in most swaps, no burner, valve, or sensor replacement is required. Standardizing a treater fleet runs a few hours per unit.
What if my pad has no power?
+
The unit runs on facility 12–24 V DC, or on a solar + dual-battery power package we design and build in-house — panel, batteries, and charge controller mounted on the same stand. No trenching, no generator, no cell service required.
How is it priced?
+
Every unit is built to order — ignition type, flame proving, power package, and trim options set the price, so we quote each build rather than publish a one-size number. Quotes are same-day: text a photo of your existing panel and burner to (432) 227-4106.
“Platinum 600”, “Platinum Control”, and “Profire” are trademarks of their respective owners, referenced only to identify equipment Reliable Oilfield Services replaces and services. ROS is independent and is not affiliated with, authorized by, or endorsed by either company.